Aluminum

The lightweight aluminum housings, visors, and doors are equipped with stainless steel hardware. Door and lens gaskets make the signal weatherproof and dust-tight, while the integral visor rims prevent light leakage.

• Material: Die-cast aluminum alloy housing and door. Stainless
  steel hardware
• Finish: Electrostatically applied powder coat with five stage
  iron phosphate treatment
• Reflector Snap-out assembly: Swing out molded frame. Lane
  control uses a standard reflector
• Lamp recepticle: Heat-resistant molded phenolic, Rotatable through
  360: pre-wired with 26” #18 AWG 105°C type TEW
  color-coded leads with Quick-disconnect terminals.
• Wire opening between sections: Accommodates three 3/4” diameter cables
• Signal alignment: Integral 72-tooth serrated locking ring. Adjustable in 5° steps
• Overall dimensions:
  8”(200mm) Section:
  9.75”W x 10.00”H x 6.16”D
  (248mm x 254mm x 156mm)
  
  12”(300mm) Section:
  13.25”W x 13.44”H x 6.44”D
  (337mm x 341mm x 164mm)
  
  Lane Control Section:
  13.50”W x 13.50”H x 9.75”D
  (343mm x 343mm x 248mm)
  
  
• Weight:
  8” (200mm) Section:
  7.50 Ibs. (3.4kg)
  
  12 (300mm) Section:
  12.75 Ibs. (5.7kg)
  
  Lane Control Section:
  19.25 Ibs. (8.7kg)

Polycarbonate
The lightweight, one-piece housings, doors, and visors are of ultraviolet-stabilized polycarbonate resin.The housings are injection molded with integral top, bottom, and sides. Color is impregnated in the material, which means it never needs painting, is unaffected by scratches, and is impervious to corrosive atmospheres (such as that found in coastal areas).

• Material: Ultraviolet-stabilized polycarbonate resin (having a minimum thickness of 0.100 inches), Stainless steel hardware
• Reflector: Snap-out assembly. Swing out frame. Lane control uses a standard reflector
• Lamp receptacle: Heat-resistant molded phenolic, rotatable through 360 pre-wired with 26” #18 AWG 105°C type TEW color-coded leads with quick-disconnect terminals
• Wire openings: Accommodates three 3/4” diameter cables between sections
• Terminal block:
  1-section 2-point
  2-section 3-point
  3-section 5-point
  4-section 5-point
  5-section 5-point and 5-point
• Signal alignment: Integral 72-tooth serrated locking ring, Adjustable in 5° steps
  
• Overall dimensions:
  8”(200mm) Section
  9.75”W x 10.00”H x 6.16”D
  (248mm x 254mm x 156mm)
  
  12”(300mm) Section
  13.25”W x 13.44”H x 6.44”D
  (337mm x 341mm x 164mm)
  
  Lane Control Section
  13.50”W x 13.50”H x 9.75”D
  (343mm x 343mm x 248mm)
  
  
• Weight:
  8” (200mm) Section
  7.50 Ibs. (3.4kg)
  
  12” (300mm) Section
  12.75 Ibs. (5.7kg)
  

---

Additional Information

• Peek Vehicle Signals Datasheet
• Contacting Peek for Customer Support on Signal Products
  

---

Ordering Information

To request more information about Peek signal products, please contact the Peek Traffic Sales team: